 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| AG402-86 InGaP HBT Gain Block The Communications Edge TM Product Information Product Features * * * * * * DC - 6000 MHz +17 dBm P1dB at 900 MHz +32.5 dBm OIP3 at 900 MHz 15 dB Gain at 900 MHz Single Voltage Supply Lead-free / RoHS-compliant / Green SOT-86 package * Internally matched to 50 Product Description The AG402-86 is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surface-mount package. At 900 MHz, the AG402-86 typically provides 15 dB gain, +32.5 dBm OIP3, and +17 dBm P1dB. The device combines dependable performance with consistent quality to maintain MTTF values exceeding 1000 years at mounting temperatures of +85 C and is housed in a leadfree/green/RoHS-compliant SOT-86 (micro-X) industrystandard SMT package. The AG402-86 consists of Darlington pair amplifiers using the high reliability InGaP/GaAs HBT process technology and only requires DC-blocking capacitors, a bias resistor, and an inductive RF choke for operation. The broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as GPRS, GSM, CDMA, and W-CDMA. In addition, the AG402-86 will work for other various applications within the DC to 6 GHz frequency range such as CATV and WiMAX. Functional Diagram GND 4 RF In 1 3 RF Out 2 GND Applications * * * * * Mobile Infrastructure CATV / FTTX W-LAN / ISM RFID WiMAX / WiBro Function Input Output/Bias Ground Pin No. 1 3 2, 4 Specifications (1) Parameter Operational Bandwidth Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Output IP2 Noise Figure Test Frequency Gain Output P1dB Output IP3 (2) Device Voltage Device Current Typical Performance (1) Units MHz MHz dB dB dB dBm dBm dBm dB MHz dB dBm dBm V mA Min DC Typ 900 15.0 18 25 +17.1 +32.6 +46 3.7 1900 14.3 +15.9 +29.6 4.91 60 Max 6000 Parameter Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure Units MHz dB dB dB dBm dBm dB 500 15.2 -16 -28 +17.1 +33.3 3.7 Typical 900 15.0 -18 -25 +17.1 +32.6 3.7 1900 14.3 -20 -16 +15.9 +29.6 3.9 2140 14.0 -20 -16 +15.3 +28.2 3.9 13.3 15.3 1. Test conditions: T = 25 C, Supply Voltage = +6 V, Rbias = 18.2 , 50 System. 2. 3OIP measured with two tones at an output power of 0 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature DC Voltage RF Input Power (continuous) Junction Temperature -40 to +85 C -55 to +125 C +5 V +10 dBm +250 C Rating Ordering Information Part No. AG402-86G AG402-86PCB Description InGaP HBT Gain Block (lead-free/green/RoHS-compliant SOT-86 Package) 700 - 2400 MHz Fully Assembled Eval. Board Specifications and information are subject to change without notice Operation of this device above any of these parameters may cause permanent damage. WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 1 of 5 September 2006 AG402-86 InGaP HBT Gain Block Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure MHz dB dB dB dBm dBm dB 100 15.3 -18 -23 +17.1 +33.6 3.7 500 15.2 -16 -28 +17.1 +33.3 3.7 900 15.0 -18 -25 +17.1 +32.6 3.7 1900 14.3 -20 -16 +15.9 +29.6 3.9 2140 14.0 -20 -16 +15.3 +28.2 3.9 The Communications Edge TM Product Information Typical Device RF Performance Supply Bias = 6 V, Rbias = 18.2 , Icc = 60 mA 2400 13.8 -20 -16 +14.7 +27.3 4.0 3500 13.0 -20 -17 +11.9 4.0 5800 10.7 -16 -13 1. Test conditions: T = 25 C, Supply Voltage = +6 V, Device Voltage = 4.91 V, Rbias = 18.2 , Icc = 60 mA typical, 50 System. 2. 3OIP measured with two tones at an output power of 0 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit. Gain vs. Frequency 16 14 Return Loss 0 Device Current (mA) I-V Curve 100 80 Optimal operating point 60 40 20 0 3.0 12 10 8 -40 C 6 0 1 2 Frequency (GHz) 3 4 +25 C +85 C S11, S22 (dB) -10 -20 -30 S11 S22 G a in (d B ) -40 0 1 2 3 4 5 6 3.4 3.8 4.2 4.6 5.0 5.4 Frequency (GHz) Output IP2 vs. Frequency Device Voltage (V) Noise Figure vs. Frequency Output IP3 vs. Frequency 40 35 30 25 -40 C +25 C +85 C 50 45 5 4 NF (dB) -40c +25c +85c OIP3 (dBm) OIP2 (dBm) 3 2 1 -40 C +25 C +85 C 40 35 30 20 0 0 200 400 600 800 1000 0 0.5 1 1.5 2 2.5 3 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) P1dB vs. Frequency Frequency (MHz) Output Power / Gain vs. Input Power 16 14 G a in (d B ) 12 10 8 Output Power 6 0 -12 -8 -4 0 Input Power (dBm) 4 8 4 -12 -8 Gain frequency = 900 MHz Frequency (GHz) Output Power / Gain vs. Input Power 20 O u tp u t P ow e r (d B m ) G a in (d B ) 16 12 8 4 14 12 10 8 6 Output Power 0 -4 0 Input Power (dBm) 4 8 Gain frequency = 2000 MHz 20 15 10 5 -40 C +25 C +85 C 20 O u tp u t P ow e r (d B m ) 16 12 8 4 P1dB (dBm) 0 0 0.5 1 1.5 2 2.5 3 3.5 4 Frequency (GHz) Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 2 of 5 September 2006 AG402-86 InGaP HBT Gain Block Gain vs. Frequency 16 14 12 10 8 -40 C 6 0 1 2 Frequency (GHz) 3 4 +25 C +85 C Output IP3 vs. Frequency The Communications Edge TM Product Information Typical Device RF Performance (cont'd) Supply Bias = +8 V, Rbias = 51 , Icc = 60 mA Output IP2 vs. Frequency 40 35 30 25 -40 C +25 C +85 C 50 45 40 35 -40c +25c +85c OIP3 (dBm) 20 OIP2 (dBm) G a in (d B ) 30 0 0.5 1 1.5 2 2.5 3 0 200 400 600 800 1000 Frequency (GHz) P1dB vs. Frequency Noise Figure vs. Frequency Frequency (MHz) 20 15 NF (dB) -40 C +25 C +85 C 5 4 3 2 1 -40 C +25 C +85 C P1dB (dBm) 10 5 0 0 0.5 1 1.5 2 2.5 3 3.5 4 Frequency (GHz) 0 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 3 of 5 September 2006 AG402-86 InGaP HBT Gain Block Vcc Icc = 60 mA The Communications Edge TM Product Information Application Circuit R1 Bias Resistor C4 Bypass Capacitor C3 0.018 F L1 RF Choke RF IN AG402-86 C1 Blocking Capacitor C2 Blocking Capacitor RF OUT Recommended Component Values Reference Designator 50 500 L1 820 nH 220 nH C1, C2, C4 .018 F 1000 pF Ref. Desig. L1 C1, C2 C3 C4 R1 Frequency (MHz) 900 1900 2200 68 nH 27 nH 22 nH 100 pF 68 pF 68 pF Size 0603 0603 0603 0805 2500 18 nH 56 pF 3500 15 nH 39 pF 1. The proper values for the components are dependent upon the intended frequency of operation. 2. The following values are contained on the evaluation board to achieve optimal broadband performance: Value / Type 39 nH wirewound inductor 56 pF chip capacitor 0.018 F chip capacitor Do Not Place 18.2 1% tolerance Recommended Bias Resistor Values S upply R1 value S ize Voltage 6V 18.2 ohms 0805 7V 34.8 ohms 1206 8V 52 ohms 1210 9V 68 ohms 1210 10 V 85 ohms 2010 12 V 118 ohms 2010 The proper value for R1 is dependent upon the supply voltage and allows for bias stability over temperature. WJ recommends a minimum supply bias of +6 V. A 1% tolerance resistor is recommended. Typical Device Data S-Parameters (Vdevice = +4.91 V, ICC = 60 mA, T = 25 C, calibrated to device leads) Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000 3250 3500 3750 4000 4250 4500 4750 5000 5250 5500 5750 6000 -18.19 -18.50 -16.83 -16.93 -17.66 -17.80 -18.49 -19.36 -19.88 -17.54 -18.15 -18.49 -18.96 -19.69 -20.80 -20.99 -21.07 -20.87 -20.80 -21.92 -22.58 -22.05 -19.90 -17.07 -15.48 -178.44 172.11 160.36 150.10 135.70 124.01 111.33 93.71 73.63 42.35 32.29 22.73 14.87 12.18 12.27 20.01 26.72 29.41 27.12 17.87 0.08 -37.48 -63.66 -80.82 -86.40 15.53 15.46 15.41 15.31 15.18 15.03 14.86 14.64 14.41 14.14 13.97 13.75 13.55 13.38 13.17 12.92 12.71 12.46 12.14 11.90 11.65 11.40 11.13 10.94 10.72 178.09 170.57 161.13 151.87 142.96 133.59 124.89 115.83 107.28 99.30 93.15 84.76 76.71 68.83 60.87 52.76 44.77 36.89 29.16 21.23 13.76 6.73 0.09 -6.84 -13.81 -19.37 -19.88 -20.13 -19.77 -20.35 -19.93 -19.99 -20.01 -20.03 -19.84 -20.39 -19.93 -20.04 -19.84 -19.89 -19.54 -19.72 -19.46 -19.50 -19.34 -19.07 -19.30 -18.94 -18.91 -18.78 0.13 -1.29 -5.19 -8.78 -14.22 -12.91 -15.83 -17.99 -21.53 -23.22 -26.91 -29.92 -29.06 -30.33 -33.64 -37.44 -40.93 -42.87 -46.46 -49.19 -52.55 -55.41 -57.71 -60.05 -63.88 -23.23 -23.53 -28.54 -26.58 -24.03 -20.82 -18.77 -16.93 -15.62 -13.24 -13.48 -13.77 -14.53 -15.91 -17.66 -18.43 -17.52 -15.52 -14.30 -13.30 -12.69 -12.63 -12.78 -13.03 -13.37 -7.45 -14.54 -47.63 -80.04 -97.40 -109.10 -116.78 -119.93 -123.85 -114.57 -119.97 -125.08 -133.10 -142.86 -160.49 169.33 144.79 128.38 119.24 117.02 119.14 122.44 128.57 135.45 138.40 Device S-parameters are available for download off of the website at: http://www.wj.com Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 4 of 5 September 2006 AG402-86 InGaP HBT Gain Block The Communications Edge TM Product Information This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260 C reflow temperature) and leaded (maximum 245 C reflow temperature) soldering processes. The plating material on the pins is annealed matte tin over copper. AG402-86G (Green / Lead-free Sot-86 Package) Mechanical Information Outline Drawing Product Marking The component will be marked with a "Y" designator followed by a two-digit numeric lot code on the top surface of the package. The obsolete tin-lead package is marked with an "F" designator followed by a two-digit numeric lot code. Tape and reel specifications for this part are located on the website in the "Application Notes" section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1C Passes 1000V min. Human Body Model (HBM) JEDEC Standard JESD22-A114 Class IV Passes 1000V min. Charged Device Model (CDM) JEDEC Standard JESD22-C101 Land Pattern ESD Rating: Value: Test: Standard: MSL Rating: Level 3 at +260 C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135") diameter drill and have a final plated thru diameter of .25 mm (.010"). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Thermal Specifications Parameter Operating Case Temperature Thermal Resistance, Rth (1) Junction Temperature, Tj (2) M T vs. G DL T p re TF N ead em eratu 1000 -40 to +85 C 216 C / W 149 C MTTF (million hrs) Rating 100 10 1. The thermal resistance is referenced from the hottest part of the junction to the ground lead (pin 2 or 4). 2. This corresponds to the typical biasing condition of +4.91V, 60 mA at an 85 C case temperature. A minimum MTTF of 1 million hours is achieved for junction temperatures below 177 C. 1 60 70 80 90 100 110 120 G u dL T p re(C ro n ead em eratu ) Specifications and information are subject to change without notice WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com Page 5 of 5 September 2006 |
Price & Availability of AG402-86G
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |